Local water treatment service

Water Treatment in Clearwater, FL

Free in-home water testing and straight answers for hard water, stains, odor, sediment, and whole-house filtration in Clearwater.

4.4 ppt
PFOS at the city’s RO Plant 1 — just over the federal limit of 4.0
68.0 ppb
Total trihalomethanes — 85 percent of the 80 limit
1.2 ppb
Lead, 90th percentile — well under the action level of 15
≈60 percent
of Clearwater’s water is pumped from the city’s own Floridan Aquifer wells

City of Clearwater 2025 water quality report — every figure is sourced in full below.

Whole-house softener and filtration setup with digital control heads — the kind of owner-installed system Aqua Pro fits in Clearwater homes
Real install · No stock photosWhole-house softener plus filtration with digital control heads.

What Clearwater water looks like

Clearwater does not drink the same water as the rest of Pinellas County. The city runs its own system — Clearwater Water System, Public Water System (PWS) ID FL6520336 — delivering about 11 million gallons a day. Roughly 60 percent is pumped from the city’s own wells in the Floridan Aquifer; the rest is purchased from Pinellas County Utilities. And Clearwater treats its water at three separate plants, two of them reverse osmosis (RO) plants that strip out dissolved solids, including the salts that cause hardness, before the water is disinfected with chloramines. Which plant feeds your street changes what reaches your tap, so Clearwater has to be read on its own report — and that report prints a table most utilities leave out.

The city’s 2025 water quality report includes plant-by-plant PFAS (per- and polyfluoroalkyl substances) results from samples taken December 3, 2025. PFOS (perfluorooctanesulfonic acid) read 4.4 parts per trillion at RO Plant 1 — just over the federal limit of 4.0 parts per trillion — and lower at the other two plants: 1.4 at RO Plant 2 and 1.2 at Water Plant 3. PFOA (perfluorooctanoic acid) read 2.6, 0.90, and 1.2 parts per trillion at the three plants, all under its 4.0 limit. Read those the honest way: they are single-day samples at the plants, not a violation — compliance with the 2024 limits is judged on running annual averages of compliance monitoring, which does not start until 2029 — but a reading over the limit at a plant that already runs its water through reverse osmosis is exactly the kind of number a Clearwater homeowner should know. A softener does not remove PFAS, and boiling does not either. That job belongs to a reverse osmosis unit or carbon filtration rated for PFAS — and if you want your own tap’s number instead of the system’s, that takes a certified lab test, which I can set up.

The number running closest to its cap in Clearwater is not PFAS. It is the disinfection byproducts: total trihalomethanes, formed when the chloramine disinfectant reacts with organic matter, hit a highest level of 68.0 parts per billion against a legal limit of 80 — 85 percent of the cap, with quarterly samples ranging from 32.0 to 68.8. Haloacetic acids read 32.5 against a limit of 60. The chloramine residual itself hit a highest running annual average of 3.18 parts per million against a maximum of 4.0.

What is not the story here: lead and germs. The system’s 90th-percentile lead reading is 1.2 parts per billion, well under the federal action level of 15, and copper read 0.34 parts per million against an action level of 1.3 (both from 2023 tap sampling). The city recorded zero E. coli–positive samples in 2025. I will tell you when a number is fine, not just when it is not.

One thing the city’s report does not print is a single hardness number — and with two RO plants and a purchased-water blend, there is no one honest number to print. Your hardness depends on your blend, and your blend depends on your street. That is what the free 20-minute test is for: hardness, iron, chlorine, pH (a measure of acidity), sulfur, and total dissolved solids (TDS) measured at your tap, not read off a system average. The county numbers are still worth a look for the contrast: Pinellas County water quality results — the county system’s own federal monitoring found no PFAS at its entry points, which is part of what makes Clearwater’s own numbers stand out.

Your tap, not the system average

See what Clearwater water is doing in your home.

The free test takes about 20 minutes at your tap. No obligation and no sales pitch — just your numbers, explained against the legal limits.

How we help in Clearwater

Licensed & Insured · Locally owned · Owner-installed

Start with the free test

Every recommendation follows a 20-minute test at your tap — never a sales pitch.

Step one · 60 seconds

The quick water check

Answer a few questions about what your water is doing at home.

Take the 60-second water check
Step two · 20 minutes

The free test at your tap

Hardness, iron, chlorine, pH, sulfur, and total dissolved solids — measured at your home, explained on the spot.

Book your free test

Find Out What’s in Your Water—Free.

Pick a callback time. We’ll call you back as soon as possible during business hours.

Licensed & Insured · Locally owned · Owner-installed

No obligation and no sales pitch. The test takes about 20 minutes at your tap.